User Tools

Site Tools


projets:fuz:webduino

This is an old revision of the document!


Webduino Smart

Goals

  • [OK] Flash Webduino with different IDEs
  • [OK] Check Components : pins, photocell, RGB LED, button
  • [OK?] Use OTA

Description

  • Webduino Smart USB port is only used to power the board, not for upload and monitoring
  • The chip is labeled ESP8266MOD by AI Thinker, in fact it is an ESP-12F, same as Wemos D1
  • The board includes a photocell, an RGB led and a button.
  • Unofficial tutorial in ~english, with how to flash Webduino Smart with FTDI
  • The Webduino Smart is extremely similar to the “(Gizwits) Witty Cloud” board, one is probably a clone of the other (same pin number for on-board components). The Witty Cloud board includes an FTDI daughter board which simplifies development, this daughter board may even be compatible with the Webduino Smart.

Wiring and flashing

Plug Webduino Smart using FTDI 3.3v module. Webduino and the FTDI must be powered. Webduino is powered through its micro USB port.

         Tx     Rx    
ftdi     Rx     Tx     Webduino
         Gnd    Gnd

For flashing, on Webduino Smart connect GPIO 0 to GND. (RGB goes light blue)

For rebooting, on Webduino Smart connect RST to GND

Flashing usual sequence is:

  1. Set flash position (GPIO0 on GND)
  2. Power the FTDI and the Webduino
  3. (RGB goes light blue) Disconnect GPIO 0
  4. Upload sketch… Webduino should restart in normal mode.
  5. Or disconnect GPIO 0 and restart using RST or Webduino power

Arduino IDE

Select Board : “Generic ESP8266 Module”

Platformio

Got it to work as a Wemos d1!

  [env:d1]
  platform = espressif8266
  board = d1
  framework = arduino

Components

I got blink sketch using LED_BUILTIN (2)

RGB LED

/***
   RGB sketch for webduino smart
   Board:   ESP8266
 
*/
 
#include <Arduino.h>
 
// according to https://webduino.io/en/tutorials/smart-01-information.html#on-board-components-and-pins
#define GPIO_GREEN_RGB 12
#define GPIO_BLUE_RGB  13
#define GPIO_RED_RGB 15
#define GPIO_MICRO_SWITCH_BUTTON 4
 
// https://create.arduino.cc/projecthub/muhammad-aqib/arduino-rgb-led-tutorial-fc003e
void RGB_color(int red_light_value, int green_light_value, int blue_light_value) {
  analogWrite(GPIO_RED_RGB, red_light_value);
  analogWrite(GPIO_GREEN_RGB, green_light_value);
  analogWrite(GPIO_BLUE_RGB, blue_light_value);
}
 
void showColor(int color) {
  Serial.printf("Color %d\n", color);
  switch (color) {
    case 0:
      RGB_color(255, 0, 0); // Red
      break;
    case 1:
      RGB_color(0, 255, 0); // Green
      break;
    case 2:
      RGB_color(255, 255, 125); // Raspberry
      break;
    case 3:
      RGB_color(0, 255, 255); // Cyan
      break;
    case 4:
      RGB_color(255, 0, 255); // Magenta
      break;
    case 5:
      RGB_color(255, 255, 0); // Yellow
      break;
    case 6:
      RGB_color(255, 255, 255); // White
    default:
      RGB_color(0, 0, 0); // Disabled
  }
}
 
void setup() {
  Serial.begin(115200);
  delay(10);
  Serial.println();
  Serial.println(F("Webduino smart RGB sketch: push the micro switch button to loop over colors"));
 
  pinMode(GPIO_GREEN_RGB, OUTPUT);
  pinMode(GPIO_BLUE_RGB, OUTPUT);
  pinMode(GPIO_RED_RGB, OUTPUT);
}
 
int color = 0;
void loop() {
  if (digitalRead(GPIO_MICRO_SWITCH_BUTTON) == LOW) {
    Serial.println(F("Button pressed"));
    color = ((color + 1) % 7);
    showColor(color);
    delay(200);
  }
}

Photocell

/***
   Photocell sketch for webduino smart
   Board:   ESP8266
 
*/
 
#include <Arduino.h>
 
// according to https://webduino.io/en/tutorials/smart-01-information.html#on-board-components-and-pins
#define GPIO_PHOTOCELL A0
#define GPIO_MICRO_SWITCH_BUTTON 4
 
void setup() {
  Serial.begin(115200);
  delay(10);
  Serial.println();
  Serial.println(F("Webduino photocell sketch: push the micro switch button to read photocell values"));
}
 
 
void loop() {
  if (digitalRead(GPIO_MICRO_SWITCH_BUTTON) == LOW) {
    Serial.println(analogRead(GPIO_PHOTOCELL)); // values go from 0 for complete darkness to 1024 for full bright light
  }
}

OTA

projets/fuz/webduino.1600558610.txt.gz · Last modified: 2023-02-02 22:06 (external edit)