projets:fuz:webduino
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
projets:fuz:webduino [2019-11-30 23:51] – [Wiring and flashing] fritzing image Lomanic | projets:fuz:webduino [2020-05-10 22:14] – [OTA] +link to http://www.csshl.net/content/esp8266-aggiornamenti-ota Lomanic | ||
---|---|---|---|
Line 4: | Line 4: | ||
===== Goals ===== | ===== Goals ===== | ||
* [OK] Flash Webduino with different IDEs | * [OK] Flash Webduino with different IDEs | ||
- | * Check Components : pins, photocell, RGB LED, button | + | * [OK] Check Components : pins, photocell, RGB LED, button |
- | * Use OTA | + | * [OK?] Use OTA |
</ | </ | ||
Line 12: | Line 12: | ||
* [[https:// | * [[https:// | ||
* Webduino USB port is only used to power the board, not for upload and monitoring | * Webduino USB port is only used to power the board, not for upload and monitoring | ||
- | * The chip is labeled ESP8266MOD by AI Thinker, in fact it is an ESP-12F, same as Wemos d1 | + | * The chip is labeled ESP8266MOD by AI Thinker, in fact it is an ESP-12F, same as Wemos D1 |
- | * The Board include | + | * The board includes |
* [[https:// | * [[https:// | ||
Line 27: | Line 27: | ||
{{: | {{: | ||
- | For **flashing**, | + | For **flashing**, |
For **rebooting**, | For **rebooting**, | ||
- | Flashing usual sequence is : | + | Flashing usual sequence is: |
- Set flash position (GPIO0 on GND) | - Set flash position (GPIO0 on GND) | ||
- Power the FTDI and the Webduino | - Power the FTDI and the Webduino | ||
+ | - (RGB goes light blue) Disconnect GPIO 0 | ||
- Upload sketch... Webduino should restart in normal mode. | - Upload sketch... Webduino should restart in normal mode. | ||
- Or disconnect GPIO 0 and restart using RST or Webduino power | - Or disconnect GPIO 0 and restart using RST or Webduino power | ||
Line 43: | Line 44: | ||
===== Platformio ===== | ===== Platformio ===== | ||
- | Got it to work as a Wemos d1 ! | + | Got it to work as a Wemos d1! |
[env:d1] | [env:d1] | ||
Line 54: | Line 55: | ||
I got blink sketch using LED_BUILTIN (2) | I got blink sketch using LED_BUILTIN (2) | ||
+ | ==== RGB LED ==== | ||
+ | |||
+ | <code c++> | ||
+ | /*** | ||
+ | RGB sketch for webduino smart | ||
+ | | ||
+ | |||
+ | */ | ||
+ | |||
+ | #include < | ||
+ | |||
+ | // according to https:// | ||
+ | #define GPIO_GREEN_RGB 12 | ||
+ | #define GPIO_BLUE_RGB | ||
+ | #define GPIO_RED_RGB 15 | ||
+ | #define GPIO_MICRO_SWITCH_BUTTON 4 | ||
+ | |||
+ | // https:// | ||
+ | void RGB_color(int red_light_value, | ||
+ | analogWrite(GPIO_RED_RGB, | ||
+ | analogWrite(GPIO_GREEN_RGB, | ||
+ | analogWrite(GPIO_BLUE_RGB, | ||
+ | } | ||
+ | |||
+ | void showColor(int color) { | ||
+ | Serial.printf(" | ||
+ | switch (color) { | ||
+ | case 0: | ||
+ | RGB_color(255, | ||
+ | break; | ||
+ | case 1: | ||
+ | RGB_color(0, | ||
+ | break; | ||
+ | case 2: | ||
+ | RGB_color(255, | ||
+ | break; | ||
+ | case 3: | ||
+ | RGB_color(0, | ||
+ | break; | ||
+ | case 4: | ||
+ | RGB_color(255, | ||
+ | break; | ||
+ | case 5: | ||
+ | RGB_color(255, | ||
+ | break; | ||
+ | case 6: | ||
+ | RGB_color(255, | ||
+ | default: | ||
+ | RGB_color(0, | ||
+ | } | ||
+ | } | ||
+ | |||
+ | void setup() { | ||
+ | Serial.begin(115200); | ||
+ | delay(10); | ||
+ | Serial.println(); | ||
+ | Serial.println(F(" | ||
+ | |||
+ | pinMode(GPIO_GREEN_RGB, | ||
+ | pinMode(GPIO_BLUE_RGB, | ||
+ | pinMode(GPIO_RED_RGB, | ||
+ | } | ||
+ | |||
+ | int color = 0; | ||
+ | void loop() { | ||
+ | if (digitalRead(GPIO_MICRO_SWITCH_BUTTON) == LOW) { | ||
+ | Serial.println(F(" | ||
+ | color = ((color + 1) % 7); | ||
+ | showColor(color); | ||
+ | delay(200); | ||
+ | } | ||
+ | } | ||
+ | </ | ||
+ | |||
+ | ==== Photocell ==== | ||
+ | <code c++> | ||
+ | |||
+ | /*** | ||
+ | | ||
+ | | ||
+ | |||
+ | */ | ||
+ | |||
+ | #include < | ||
+ | |||
+ | // according to https:// | ||
+ | #define GPIO_PHOTOCELL A0 | ||
+ | #define GPIO_MICRO_SWITCH_BUTTON 4 | ||
+ | |||
+ | void setup() { | ||
+ | Serial.begin(115200); | ||
+ | delay(10); | ||
+ | Serial.println(); | ||
+ | Serial.println(F(" | ||
+ | } | ||
+ | |||
+ | |||
+ | void loop() { | ||
+ | if (digitalRead(GPIO_MICRO_SWITCH_BUTTON) == LOW) { | ||
+ | Serial.println(analogRead(GPIO_PHOTOCELL)); | ||
+ | } | ||
+ | } | ||
+ | </ | ||
===== OTA ===== | ===== OTA ===== | ||
See https:// | See https:// | ||
+ | |||
+ | This was randomly working for me, laybe implement [[http:// |
projets/fuz/webduino.txt · Last modified: 2023-02-02 22:06 by 127.0.0.1